Home > Not Working > Jeep Wrangler Fuel Gauge Not Working

Jeep Wrangler Fuel Gauge Not Working

Contents

Topless wheeling contributes to these problems. If that doesn't work, it's time for a new switch. Mark helpful Your Answer Add photo Photo (optional) Related Questions 1990 Wrangler Sahara ...total loss? (read what happened) 15 answers First time jeep owner as of 4 weeks go bought it Cleanliness is Next to Firewall Symptom: Weird or random functionality of things. http://helpsbs.com/not-working/94-jeep-wrangler-speedometer-not-working.html

As you remove the cluster from the dash frame be careful not to snatch the dash harness causing more connection issues. Just rub a light coat on the contacts and allow it to sit for a few minutes. I have 24,500 miles, so I wonder if they even changed fuel pump, I am going to have a friend drop fuel tank see if its the fuel pump we bought I'm about out of ideas.

Jeep Wrangler Fuel Gauge Not Working

Use new dielectric grease prior to reassembly. About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! These jeep's don't have many fuses and I checked them all. 1 fuse block under the drivers dash and 1 in front of the battery under the hood.

What it does do is prevent more corrosion from forming. Req'd. jessicavan00 21,579 views 0:59 Jeep Frame Repair - Duration: 4:43. Jeep Yj Gas Gauge Reads Full A new speedo cable should be used that screws onto the gauge.

Buyout price $20,500 only 23000 miles. 14 answers With what I may be looking to replace it with I would have to buy used. 2008 or 9 Tahoe with much higher 1991 Jeep Wrangler Fuel Gauge Not Working Find the bundle of black wires bolted to the body near the fuse block, make sure the connection is tight and clean, then follow the wire back towards the dash, looking After testing the bulb colors under dark conditions, I opted to go with an amber color bulb instead of the clear, red or green. The coolant temperature sender is located at the rear of the cylinder head on 4cyl.

Being a tech really helps the process along nicely and I can see that. Jeep Gas Gauge Not Working I bought it with 21,000. Number 8 ring clamps were used for the terminal connections and the ring clamps/wires were crimped and soldered for extra strength. Thanks.

1991 Jeep Wrangler Fuel Gauge Not Working

Remove the metal dash and admire the maze of wires! Suggested Questions/Answers : Loading ... Jeep Wrangler Fuel Gauge Not Working Please try again later. Jeep Yj Fuel Gauge Stuck On Full Sign in to report inappropriate content.

That's how I wanted the dash in my 1991 Wrangler to be. http://helpsbs.com/not-working/why-is-my-xvm-not-working.html Transcript The interactive transcript could not be loaded. Each connector you get clean, put some dielectric grease on EVERY electrical connection. It's been 6 months it works fine but gas gauge still doesn't work. 1989 Jeep Wrangler Fuel Gauge Not Working

Fix: The clockspring is located behind the steering wheel, and steering wheel removal is necessary to remove it. Secure the dash to the tub with the stock bolts and you're done! and end with a "?" Be clear and specific Use proper spelling and grammar ASK NOW

all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Check This Out Especially ones that have been wheeled a lot.

Tracing each wire, we made a table showing gauge, wire color, polarity and pin number on the connector. 1990 Jeep Wrangler Fuel Gauge Problem This color provides a nice illumination of the gauge faces and it just looks cool! Loading...

Motor Trend Channel 3,888,612 views 25:52 Jeep Wrangler YJ - 15 to 20 gallon gas tank mod - FREE - Duration: 13:08.

Not only that it also helps seal out water from those nice clean connections you established for your gauges. checked every connector under the dash and hood. I found out later that the factory ohm readings for my 1991 YJ (2.5l) are 1 ohm empty and 88 ohms full. 95 Jeep Wrangler Fuel Gauge Not Working We wired in some relays to take the current out of the switch, but ended up with the same problem again due to not replacing everything the first time.

With the gauges installed in the dash, the wiring harness for the gauges/lights were attached and secured to the back of the dash using zip ties. If they aren't test down the length of each of the battery cables until you find the issue. Soooo nice. this contact form call Water Temperature (100-250oF) 2 in. 5737 Oil Pressure (0-100 psi) 2 in. 5721 Removal of the Stock Dash and Gauges To remove the stock dash, first disconnect the negative